18K vs 14K Gold Body Jewellery: Which Should You Stock?

What the karat changes on the bench, at the counter and in your stock.

By The Tremun Team · Barcelona, Spain · Updated 18 November 2026

14K gold is 58.5% gold. 18K gold is 75% gold. The rest is alloy, and the alloy sets the colour, the hardness and how a piece wears. This guide is for piercers and studio buyers. It compares 14K and 18K gold body jewellery honestly, because both karats have a place in a professional studio. By the end, you can choose a karat for each client. You can also check a gold piece at the bench and write a clear email to your supplier. It comes from more than 10 years of experience supplying professional piercers across Europe.

En bref

Five rules for choosing gold

14K58.5% gold

Best for: everyday pieces, a lighter yellow

18K75% gold

Best for: signature pieces, curated ears, deep colour

  1. Buy solid gold only. Plated and filled pieces are a different product.
  2. 14K is 58.5% gold, 18K is 75%. The rest is alloy, so ask what it is.
  3. Hardness depends on the alloy and how it is worked, not on karat alone. 18K has a deeper, warmer yellow.
  4. For white gold, ask if the piece is plated. Plating wears over time.
  5. Plan gold by collection and colour. Use 18K for signature pieces and curated ears.
Already approved?See the 18K line
Vous êtes perceur professionnel ? Tremun fournit uniquement les studios. Voir les prix de gros

What 14K and 18K actually mean

Karat is the share of pure gold in an alloy, measured in 24 parts.

14K means 14 parts gold in 24. The exact maths gives 58.3%, but the trade standard is 58.5% gold. This figure is a minimum, never rounded down. 18K means 18 parts gold in 24, which is 75% gold.

So a 14K piece is 41.5% other metals. An 18K piece is 25% other metals. That difference drives almost everything else in this guide.

Gold content

Chart comparing 14K gold at 58.5% gold and 18K gold at 75% gold, with the alloy share of eachBar chart. 14K gold is 58.5% gold and 41.5% alloy. 18K gold is 75% gold and 25% alloy.14K58.5%41.5%18K75%25%0%50%100%
14K is 58.5% gold and 41.5% alloy. 18K is 75% gold and 25% alloy.

The other part: the alloy

Pure gold is very soft. Other metals make it harder and change its colour.

Yellow gold usually mixes gold with silver and copper, often with a little zinc. Copper makes the colour warmer. Silver makes it paler. White gold uses white metals, often palladium. Some white golds in the wider jewellery trade use nickel.

Two pieces with the same karat can use very different alloys. That is why "14K" or "18K" on a label does not tell you everything. Ask your supplier what the other metals are.

Read the stamp

A hallmark stamp shows gold content in parts per thousand. So 14K reads as 58.5% gold and 18K as 75% gold. Very small pieces are often not stamped. In France and Spain, small gold items can be exempt from the official mark. The traditional weight threshold is 3 g. A missing stamp on a tiny top is not proof of anything. Ask the supplier for a written declaration of karat instead.

14K vs 18K gold at a glance

14K and 18K are both solid gold, with different strengths. Use this table at the bench or when you plan an order.

14K vs 18K gold body jewellery compared (typical values; the exact result depends on the alloy)
Property14K58.5% gold18K75% gold
Gold content58.5% gold, 41.5% alloy75% gold, 25% alloy
Colour (yellow)Lighter, paler yellowDeeper, warmer yellow
Colour (white)Depends on alloy and any platingDepends on alloy and any plating
HardnessDepends on the alloy and how it is workedDepends on the alloy and how it is worked
Scratch behaviourShows fine marks with wear; can be re-polishedShows fine marks with wear; can be re-polished
Weight, same designLighterRoughly 15–20% heavier (yellow)
Price logicLess gold per pieceMore gold per piece
Best forEveryday pieces, a lighter yellowSignature pieces, curated ears, deep colour

See the 18K line →

Colour: yellow and white gold

18K yellow gold looks deeper and warmer because it holds more gold. 14K yellow is lighter, because more alloy dilutes the colour.

Every maker uses its own recipe. Two "14K yellow" pieces from two suppliers can look different side by side. The same is true for 18K. Keep one 14K and one 18K piece at the counter as a colour reference. Clients usually see the difference quickly.

White gold and rhodium plating

White gold is gold mixed with white metals, and many white gold pieces are rhodium plated.

Rhodium is a thin, bright white coating. In jewellery in general, it gives white gold a colder, brighter white. The coating wears on contact points over time. Then the base alloy shows through, which can look slightly warm or grey. A jeweller can re-plate the piece.

Not every white gold is plated. Some palladium white alloys are white enough without it. So ask two questions before you order: is this piece plated, and what is the base alloy? Tell your clients the answer before the fitting.

What to expect from white gold

White gold is a gold colour, not a silver or platinum colour.

Set clear expectations at the counter. An unplated white gold can show a soft, warm grey tone. A plated white gold looks brighter at first, then can change slowly at contact points. Neither is a fault. Both are normal behaviour for the material.

Place a white gold piece next to titanium before the fitting. The client sees the real tone, and there is no surprise later. If a client wants a cold, bright white for many years, talk about plating and re-plating first.

Hardness, scratches and wear

Hardness depends on the alloy and how it is worked, not on karat alone.

A common belief is that 14K is always harder than 18K. Published alloy data does not support this rule. Typical hardness figures for 14K and 18K overlap widely. Many common 18K yellow alloys are as hard as 14K yellow, or harder.

One refiner's data shows the pattern. Annealed 14K yellow measures about 100 HV (Vickers hardness). Annealed 18K yellow measures about 135 HV. Cold work raises both, to about 190 HV and 225 HV. Cast, annealed and worked gold all behave differently.

What is true for every karat: gold is generally softer than ASTM F136 titanium. Every gold piece shows fine marks with wear. A hand polished, mirror finish can be restored. Each polish removes a tiny amount of metal.

Above 18K

The Association of Professional Piercers (APP) considers gold above 18K too soft for body jewellery. It scratches and nicks too easily. So the APP window for body jewellery is 14K to 18K.

Settings in gold: prong, bezel and flush

The setting holds the stone, and its design matters more than the karat. Learn the three main types. Then you know what to check at the bench.

Common stone settings in gold body jewellery
SettingHow it holds the stoneWhat to check at the bench
Prong (claw)Thin metal claws grip the stone at its edgeProng tips sit tight on the stone; no lifted or bent claw
Serti closA metal rim goes all around the stoneThe rim is closed and even; the stone does not turn
FlushThe stone sits inside the metal surfaceThe stone is level with the surface; no gap at the edge

Prong settings show more of the stone and let light reach it. The claws are small, so they need gentle handling in any karat. Clothes, towels and hair can catch on them.

Bezel settings protect the stone edge with a full metal rim. They show less of the stone, but they have a smooth outline. They can suit clients who often catch their jewellery.

Flush settings sit the stone inside the metal. The surface is very smooth. They can suit a minimal style and small stones.

Settings and karat

Prong strength depends on the design, the wire thickness and how the metal is worked. This is true in 14K and in 18K. A thin claw can open in any karat. Ask your supplier how its prongs are made.

So do not choose a karat for a setting. Choose a supplier whose settings you can check and trust. Then choose the karat for colour.

Checking prongs at the bench

Use this routine when an order arrives, and again before each fitting.

  1. Look under a loupe. Check each prong tip. It should touch the stone and sit flat.
  2. Count the claws. A 3-prong top must have three claws in contact with the stone.
  3. Check for movement. The stone should not turn or move in its setting.
  4. Check the stone level. It should sit straight, not tilted.
  5. Feel the edges. Run a cotton pad over the top. A lifted claw can catch the fibres.

If a claw looks lifted, do not push it back yourself. Contact your supplier first. Setting repair is jeweller's work.

Stones in gold: moissanite, natural stones and zirconia

The stone and the gold colour work together. Choose them as a pair, not one by one.

Gold body jewellery often uses three families of stones. Each one has its own look and its own care needs.

  • Lab-grown moissanite. A lab-grown stone with strong sparkle. White lab-grown moissanite looks bright against yellow gold.
  • Natural stones. For example, natural ruby, garnet or tsavorite. Each natural stone is a little different in colour. A small natural ruby gives a strong colour point.
  • Swarovski zirconia. A cut cubic zirconia with a wide range of colours. It lets you build colour stories, such as champagne, amethyst or clear white.

Stones differ in hardness and care needs. Ask your supplier about each stone, or check the product page.

Colour pairing with yellow and white gold

Yellow gold warms every stone. White gold cools it.

Stone and gold colour pairing at the counter
Couleur de la pierreWith yellow goldWith white gold
Clear white (lab-grown moissanite, white zirconia)Strong contrast; the stone looks brightCalm, all-white look
ChampagneSoft, warm harmony; a quiet lookLight contrast; looks warmer
Amethyst / purpleRich contrast; the purple looks deeperCool and calm
Red (natural ruby, garnet)Classic warm pairing; a strong colour pointBright, modern contrast
Green (tsavorite, emerald green)Warm and vividFresh and cool

At the counter, ask the client one question first. Which gold colour do you already wear? Then choose the stone. Many clients keep one gold colour across the ear.

Tremun Gold · 18K · Made in Italy

Stones in 18K gold

Threadless and internally threaded tops

The closure decides how you fit a top. Learn the routine for each type.

Threadless tops at the bench

A threadless top stays in place by tension. You bend the pin a little, then push it into the post. The bend creates friction inside the post.

  1. Bend gently. Make one small, smooth bend. A small bend is usually enough.
  2. Do not over-bend. A sharp or deep bend can stress the pin. It can also make the top hard to remove.
  3. Do not re-bend many times. Bending the same point again and again can weaken the pin.
  4. Check the tension. Push the top in and pull it gently. It should hold firmly and come out with a clear, steady pull.
  5. Check the gauge. Check the pin gauge listed on the product against your posts. Mixed gauges do not hold well.

Follow the bend guidance from the maker of each piece. Each design can need a slightly different touch.

Internally threaded tops

An internally threaded top screws into a post with a matching thread. It does not need any bending. Some clients and piercers prefer this closure for certain placements.

The rule is simple: the thread must match. Check the thread size listed on the product before you pair it with a post. Our guide to internally threaded body jewellery explains how thread sizes work.

In the Tremun 18K line, Rhea Big - White SW is an internally threaded top. Check the thread size listed for compatibility with your posts.

Care and re-polishing

Gold keeps its look with simple care and the right tools. Teach clients the basics at the fitting.

  • Daily wear. Gold shows fine marks over time. This is normal for every karat.
  • Cleaning. Mild soap, warm water and a very soft brush usually work for gold pieces. Rinse well and dry with a soft cloth.
  • Polishing cloth. A jewellery polishing cloth brings back the shine on smooth surfaces. Use a clean cloth only for gold. Polish gently around prongs, so the cloth does not catch a claw.
  • Ultrasonic cleaners. Use them with caution. Some stones and some settings may not suit ultrasonic cleaning. Check with your supplier before you clean.
  • Re-polishing. A hand polished, mirror finish can be restored by a jeweller. Each polish removes a tiny amount of metal. Do not re-polish more often than needed.
  • White gold. If a white gold piece is plated, plating can be renewed by a jeweller.

Keep this short. One clear care card at the counter is better than a long talk.

Weight and price: why 18K costs more

18K costs more for two reasons: more gold per gram, and more grams per piece.

First, 18K holds 75% gold and 14K holds 58.5%. That is about 1.28 times the gold in every gram.

Second, 18K is denser. Typical 18K yellow alloys have a density of about 15.5 g/cm³. Typical 14K yellow alloys are about 13–13.5 g/cm³. So the same design in 18K yellow is roughly 15–20% heavier. Some sources say the weight is the same. For identical designs, that is not correct.

Key number

≈1.5×

The same design in 18K yellow holds about 1.5 times the pure gold of 14K yellow (approximate).

This is the honest way to explain the price gap. The client pays for metal, not for a label.

Plated, filled or solid: why studios use solid gold

Solid gold is gold alloy all the way through. Plated and filled pieces have a gold layer over another metal.

Gold-plated, gold-filled and solid gold compared
TypeWhat it isWhat happens with wear
Gold-platedA very thin gold layer over another metalThe layer wears through and the base metal shows
Gold-filledA thicker gold layer bonded to another metalStill two metals; the layer can wear or chip
Solid goldGold alloy of the stated karat, all the way throughSame metal under the surface; can be re-polished

Vermeil is a gold layer over silver. It works like plating. A plated piece that loses its colour is hard to explain at the counter. Your client remembers who fitted it. Solid gold avoids that problem.

What APP guidance and EU rules say

Two references matter most for gold body jewellery in Europe: APP guidance and EU REACH. Here are the facts, in plain words.

APP: solid 14K or higher

The APP lists solid 14K gold or higher for initial jewellery, and it sets requirements for the alloy. Yellow, white and rose gold are all included.

The APP also lists what it does not accept for fresh piercings. Gold-plated, gold-filled and gold overlay or vermeil pieces are not accepted. And, as noted above, it considers gold above 18K too soft. Read the full wording on the Association of Professional Piercers (APP) page before you quote it to a client.

EU REACH: nickel release limits

EU REACH limits how much nickel a post assembly may release, not how much nickel it contains.

The rule is in REACH Annex XVII, entry 27. Post assemblies inserted into pierced parts of the body must release less than 0.2 µg/cm²/week of nickel. The test method is EN 1811. This is a legal release limit for products on the EU market. You can ask your supplier for an EN 1811 test report for the alloy.

Questions to ask your gold supplier

Clear documents protect your studio's reputation and inform your client. Screenshot this list and use it for your next gold order.

Before you order gold

  1. Solid or not: Is the piece solid gold, and which karat?
  2. Alloy: What metals make up the rest of the alloy?
  3. White gold: Is the piece plated? If yes, with what?
  4. Nickel release: Is there an EN 1811 test report for the alloy?
  5. Marking: Is the piece stamped? If not, do you give a written karat declaration?
  6. Documents: Can you share a declaration or certificate for the batch?
  7. Stones: Is it lab-grown moissanite, a natural stone or cubic zirconia? How is it set?
  8. Closure: Is the top threadless or internally threaded? Which gauge or thread size?
  9. Finition : What is the finish called, for example hand polished, mirror finish?
  10. Care: Can the stone and setting go in an ultrasonic cleaner?

At Tremun

Need documentation for a Tremun gold piece? Ask us on WhatsApp: +34 675 014 620. We share documentation on request.

Which karat for which client

Let colour, wear and the client's goal decide the karat. Which of these clients do you see most?

Which karat for which client and placement
Client or situationKaratPourquoi
First gold piece, worn every day14K18KBoth are solid gold; let the yellow tone decide
Prefers a lighter, paler yellow14KMore alloy gives a lighter tone
Wants the deepest, warmest yellow18KMore gold, warmer tone
Delicate prong setting for daily wear14K18KAsk for the alloy; design and wire matter more than karat
Curated ear or a statement piece18KDeep colour, and one collection keeps the tone even
Wants a white gold look14K18KAsk your supplier about plating and alloy
Initial piercingSolid 14Kor higherAPP guidance and your own protocol

Not sure? Let the client compare both tones on a white card. Your bench experience always comes first.

How to explain 14K vs 18K at the counter

Clients do not need metallurgy. They need one clear reason to choose.

At the counter

  1. "Both are solid gold. 14K is 58.5% gold, 18K is 75% gold."
  2. "18K has a deeper, warmer yellow. 14K has a lighter yellow tone."
  3. "The same design in 18K weighs more and holds more gold. That is why it costs more."

Then show the difference. Place a 14K and an 18K piece side by side on a white card. The client sees the colour difference directly. Let the client choose the colour they love.

Talking about value without prices

Start with what the client gets, then talk about cost.

Many clients ask "how much?" first. Answer with value before you give a number. Four points are enough.

  1. Metal. "This is solid 18K gold, 75% gold all the way through."
  2. Making. Name where and how the piece is made, if your supplier states it. For example, "designed and made in Italy, hand polished, mirror finish."
  3. Stone. Name the stone exactly. For example, "lab-grown moissanite" or "natural ruby".
  4. Documentation. "I can show you the supplier's information for this piece."

Then give the price with confidence. A client who understands the piece compares value, not only numbers.

Matching yellow tones and planning curated ears

Curate each ear from one collection, so the yellow stays the same.

Yellow gold changes with the alloy recipe. Two 18K yellow pieces from different makers can show a different warmth. In a curated ear, clients can notice this quickly.

So build each look from one collection when you can. Keep pieces from different lines in separate trays. A client may bring a piece from elsewhere. Compare it under neutral light before you add a new piece next to it.

Planning a curated ear in 18K

  1. Choose one focal piece. Pick one stronger design, such as a cluster or a coloured stone.
  2. Add two or three supporting pieces. Use smaller stones or plain gold designs. Plain gold balances the stones.
  3. Keep one gold colour. Mix stones, not metals, for a calm look.
  4. Use left and right designs. Some designs come as a pair, made for each side. Aelia Left - White SW pairs with Aelia Right, for example.
  5. Repeat one stone colour. Champagne in two places, or white in three, links the whole ear.
  6. Plan for later. Leave room for one more piece. Clients often come back to complete the look.

Show the plan before the fitting. Hold two or three shortlisted pieces next to the ear. The client chooses a whole look, not a single top.

Displaying gold in the studio

Gold needs space, light and clear labels. A crowded tray makes every piece look smaller.

  • Light. Use neutral, daylight-white lighting. Very warm light can make 14K and 18K yellow harder to tell apart.
  • Background. Cream or dark trays both work. Test your pieces on each and choose what shows the colour best.
  • Groups. Group pieces by collection, then by gold colour. This keeps tones even within each tray.
  • Labels. Write the karat, the gold colour and the finish on each label. For example, "18K yellow gold · hand polished, mirror finish".
  • Curated looks. Show one or two complete ears on a display ear. Clients understand a look faster than a single top.
  • Reference pair. Keep one 14K and one 18K piece ready for colour comparison.
  • Loupe. Keep a loupe at the counter. Let clients see the stone and the setting up close.

Why Tremun works in 18K

Tremun Gold is our renewed 18K line, designed and made in Italy. We chose 18K for four reasons.

  1. Colour depth. 18K yellow gold has a deep, warm colour. It gives our designs a rich, even tone across a curated ear.
  2. Gold content. 18K is 75% gold. Your client gets more gold in every piece.
  3. Italian design and making. Every piece in our renewed 18K line is designed and made in Italy.
  4. Hand polish. Every Tremun Gold piece is hand polished, mirror finish. The finish is part of the product name, because it is part of the product.

The line includes threadless tops in yellow gold with lab-grown moissanite, natural stones and Swarovski zirconia. It also includes an internally threaded top and solid 18K clicker rings in yellow and white gold. You can see them in real pieces below.

Building your gold stock

A clear gold stock has a job for each piece. Plan it by collection and colour, not only by karat.

  1. Decide your everyday gold. If you stock 14K from other lines, use it for everyday pieces and clients who prefer a lighter yellow. Source each karat from one line, so colours match.
  2. Add an 18K signature selection. A curated set for your display case. It gives your display a focal point and clients a clear choice. At Tremun, this is our renewed 18K line.
  3. Build curated looks, not single pieces. Choose a focal piece and two or three supporting pieces from the same collection.
  4. Cover both colours. Yellow first, then white for clients who ask for it.
  5. Start small and adjust. With no minimum order at Tremun, you can test a few 18K pieces and reorder what sells.

Start with designs that already sell well in titanium at your counter. Then add stronger pieces, such as clusters and coloured stones. Other pieces in the line include Prong Push Pin - Moissanite and Prong Push Pin - Natural Tsavorite. There is also Clicker Ring - 18K Yellow Gold 16G.

Tremun Gold · Solid 18K gold · Designed and made in Italy

See Tremun 18K gold in real pieces

For professional piercers

See prices for Tremun Gold in 18K

Tremun sells only to professional piercers and studios. Register to see prices after approval.

  • More than 3,500 studios trust Tremun
  • Sans minimum de commande
  • Free DHL Express from €350 (VAT incl.)
  • WhatsApp +34 675 014 620
Register your studio →See the 18K line →

Questions fréquentes

Is 14K or 18K gold better for piercings?

Neither karat is better in every case. 14K is 58.5% gold, with a lighter yellow. 18K is 75% gold, with a deeper, warmer yellow, and suits signature pieces and curated ears. Hardness depends on the alloy and how it is worked, not on karat alone. Both sit inside the APP window of solid 14K to 18K.

Can solid 14K gold be used for initial piercings?

Yes. The APP lists solid 14K gold or higher for initial jewellery. It also sets requirements for the alloy, so read its full wording on the APP website. Plated, filled and vermeil pieces are not accepted for fresh piercings. Ask your supplier for the alloy and a written karat declaration, and follow your own studio protocol.

Why does 18K gold cost more than 14K?

18K holds 75% gold, against 58.5% in 14K. That is about 1.28 times the gold per gram. 18K is also denser, so the same design is roughly 15–20% heavier. Together, the same 18K yellow piece holds about 1.5 times the pure gold of 14K yellow. The price follows the metal.

Is 18K gold too soft for body jewellery?

No. The APP considers only gold above 18K too soft for body jewellery. Hardness depends on the alloy and how it is worked, not on karat alone. Many common 18K yellow alloys are as hard as 14K yellow, or harder. Every gold piece shows fine marks with wear, and a hand polished, mirror finish can be restored.

Is white gold body jewellery rhodium plated?

Often, but not always. Many white gold pieces in the jewellery trade carry a thin rhodium coating for a brighter white. The coating wears on contact points, and the base alloy then shows. Some palladium white alloys need no plating. Ask your supplier whether each white gold piece is plated, and what the base alloy is.

Is gold-plated jewellery acceptable for initial piercings?

No. APP guidance does not accept gold-plated, gold-filled or gold overlay and vermeil pieces for fresh piercings. All of these put a thin gold layer over a base metal. The layer can wear or chip off with time. Solid gold is the same alloy all the way through, so the surface can be re-polished.

What documents should I ask a gold supplier for?

Ask for the karat and the full alloy in writing. For white gold, ask whether the piece is plated. Ask for an EN 1811 nickel-release test report and a declaration or certificate for the batch. Small pieces are often not stamped, so a written declaration matters. Tremun shares documentation on request via WhatsApp +34 675 014 620.

How do I handle a threadless top at the bench?

Make one small, gentle bend in the pin, then push the top into the post. Check the tension with a light pull. Do not over-bend, and do not re-bend the same point many times. Check the pin gauge listed on the product against your posts. Follow the bend guidance from the maker of each piece.

Can I clean gold jewellery with stones in an ultrasonic cleaner?

Use an ultrasonic cleaner with caution. Some stones and some settings may not suit ultrasonic cleaning. Mild soap, warm water and a very soft brush usually work for gold pieces. Check with your supplier about the specific stone and setting before you clean it.

How can my studio buy Tremun Gold in 18K?

Tremun sells only to professional piercers and studios. Register at tremunpiercing.com/registration/ and our team checks each account. Prices are visible after approval. There is no minimum order, and DHL Express shipping is free from €350 (VAT incl.). Our renewed 18K line is designed and made in Italy, hand polished, mirror finish.

The Tremun Team